anchor bolt specifications and substitution

Anchor Bolt Source provides custom manufactured and stock threaded anchor rods and bent anchor bolts in galvanized or plain finish in various ASTM grades to fit your project requirements

Where ASTM A449 becomes a potential alternative for A325 is when the strength of an A325 is desired but the actual part is an anchor bolt or a configuration other than a heavy hex bolt for steel to steel connections ASTM A449 covers

2010 2 20 nbsp 0183 32 Anchor Bolts amp Bent Bolts 11 1 A Bolts Standard 11 2 U Bolts Long Tangent 11 3 Eyebolts Regular Pattern 11 4 Eyebolts Shoulder Pattern 11 5 Rod End Eyebolt Blanks 11 6 Metric Fasteners Hex Head Cap Screws 12 1 Weights of Hex Head Cap Screws 12 2 Socket Cap Screws amp Flat Head Socket Caps 12 3 Socket Set

There are very few companies besides Portland Bolt if any that inventory F1554 Grade 36 headed anchor bolts Portland Bolt stocks ASTM F1554 Grade 36 hex head anchor bolts in 3 4″ 7 8″ and 1″ diameters and will manufacture any diameter and length combination that is not in stock ASTM Spec Mechanical Properties

ASTM F1554 F1554 is the ASTM International specification for anchor bolts Until the ASTM F1554 specification was introduced anchor bolts did not have a specification of their own They were most commonly specified under ASTM A307 Carbon Steel Bolts and Studs or simply as ASTM A36 actually a material specification not a bolt specification

Specifications ASTM F1554 F1554 covers anchor bolts that are intended to be embedded in concrete in order to fasten structural supports to the concrete foundation These anchor bolts are available in Grade 36 Grade 55 and Grade 105 – the number after the grade designates the fastener s minimum yield strength measured in ksi

2015 5 1 nbsp 0183 32 According to ASTM F1554 07a when Grade 36 is specified a weldable Grade 55 may be furnished at the supplier s option Portland Bolt may use this substitution in situations when it will save the customer time and or money This allowance is useful for Portland Bolt when asked to supply Heavy Hex Grade 36 bolts because we stock blanks that are already

2019 5 7 nbsp 0183 32 BAC Part A Z MIL SPEC Part Item Name View amp Buy Online BACB30LR4 6 MS24694S101 Machine Screw MS24694S101 BACB30MT5 10 NAS625 10 Shear Bolt NAS625 10 BACB30N6 7 NAS1446 07 Pin rivet NAS1446 07 BACB30NE12D26 NAS6603 20 Shear Bolt NAS6603 20 BACB30NE3 11 NAS6603 11 Shear Bolt NAS6603 11

2020 5 18 nbsp 0183 32 Wedge anchor DBZ Aerated concrete anchor HPD Page 304 Sleeve anchor with screw and washer HAM with bolt Page 304 Hard sleeve anchor HAM without bolt Hook and ring anchors HA 8 Page 305 Plastic Anchors Frame anchors HRD C HRD CR HRD CR2 HRD H HRD HF HRD HR HRD HR2 HRD K Page 306 311 HRD KR2 HRD P HRD PR2

APPLICATION This bolt spec is the most commonly used for any general application for bolting This bolt spec is for bolts anchor bolts and studs that have a minimum tensile strength of 60 KSI and these bolts are used for general applications

2011 10 9 nbsp 0183 32 SUBSTITUTE MATERIAL JIS BS DIN FOR ASTM SPECIFICATION CONTENTS Section 1 Scope 2 Basis 3 Additional Requirements 4 Table 5 Table 1 Plates 6 Table 2 Pipes 7 Table 3 Tubes 8 Table 4 Forging 9 Table 5 Castings 10 Table 6 Bolts and Nuts 11 Table 7 Bars and Shapes 12 Table 8 Piping Fittings

2017 8 31 nbsp 0183 32 Example Anchor bolts are assumed to be made from A36 rod stock and of embedment length sufficient to fully develop the allowable tensile capacity 0 6 215 Fy of the diameter of rod used A 1 2 diameter anchor bolt has the following capacity 0 6 215 36 000psi 215 π 215 0 52 4 4 240 psi as noted in the Table The capacity of any

All F1554 anchor bolt grades have a maximum strength requirement A193 grade B7 which is readily available as all thread rod possesses a minimum tensile strength requirement that exceeds the maximum tensile strength of F1554 grade 55 Therefore this is

2014 10 1 nbsp 0183 32 Regarding anchor bolts ASTM A449 is not a material that should be specified Regardless our steel fabricating customer often see drawings calling out for A 449 anchor bolts or fully threaded studs This is frequently DOT Highway work where AASHTO specs are more common The document that controls anchor bolt manufacturing is ASTM