zj tie rod upgrade how to:

2017 9 8 nbsp 0183 32 Then use a ZJ tie rod or other tie rod upgrade Iron Man Andy also has a good replacement that doesn t have tie rod roll too Also look into dropping the frame end of the track bar down so your track bar and drag link remain parallel That will retain your factory

Zj Tie Rod Upgrade Tj Zj Tie Rod Upgrade Jeepforum Com Jul 06 2018 183 the ds1312 is the drag link or passenger side tie rod end moog part number for the zj grand cherokee Everything you need for anything you drive Ill be prepping and painting the tie rod as

2010 1 6 nbsp 0183 32 Any tie rod from a V8 ZJ will work just makes sure it s a V8 or you ll just get the same tie rod as your XJ currently has The local pick and pulls usually have one or more available and for my that s the best way to get one of these

2016 6 28 nbsp 0183 32 Jeep Tie Rod Upgrade using OEM V8 ZJ parts Watch later Share Copy link Info Shopping Tap to unmute If playback doesn t begin shortly try

Here s a simple upgrade that you will love Most of us that wheel our TJs have personally experienced or at least seen a bent tie rod on the trail It s a very common occurrence because the stock tie rods are not that strong They stick out in front of your differential

2015 3 15 nbsp 0183 32 Re DD Steering upgrade which one For the price of a NEW V8 ZJ tie rod setup you can get an aftermarket tie rod TRE s Before I got my currie steering I was using the IM4x4fab solid TRE and 3 4 ton rod ends with stock drag link Never had an issue That setup will be going on my MJ for now

Today s Posts Member List Calendar BOD Contact Info Sponsors Sponsor Qualifications LSJC Bylaws Forum Tech Stuff General Tech Topics If this is your first visit be sure to check out the FAQ by clicking the link above You may have to register before you can post click the register link above to proceed

ZJ tie rod conversion Close 3 Posted by 5 years ago ZJ tie rod conversion Anybody done this for a Jeep tj Heard it was a good economic way to beef it up and wanna know how to go about this also I have a 2 inch lift 13 comments share save

2009 6 28 nbsp 0183 32 I used the V8 ZJ tie rod for many years since before the Currie linkage even came out It s more rock tolerant because it s a solid forging as you mention but it s a forging because it has bends in it which is why it s different at all to clear the oil pan of the 5 2 5

Anybody done this for a Jeep tj Heard it was a good economic way to beef it up and wanna know how to go about this also I have a 2 inch lift

2014 2 18 nbsp 0183 32 I m upgrading to the ZJ tie rod on my TJ The main Tie Rod PN DS1312 has no grease fitting on the end that marries with the drag link the grease fitting is on the side of the joint not the face if it was on the back face of the TRE like the short side it would hit

2021 6 6 nbsp 0183 32 We purchased a ZJ tie rod for a 1995 1998 Jeep Grand Cherokee V8 It is compatible and is a simple quot disconnect connect quot process for our 2000 Jeep XJ So Joe

2011 7 21 nbsp 0183 32 bent mine on a stump the other day i know about the zj stuff being a good upgrade and i can easily fix this one or replace it with an xj one but I m quite pressed for time these days and would like to know if i can just grab a zj one and have it be a simple direct bolt

2011 7 21 nbsp 0183 32 bent mine on a stump the other day i know about the zj stuff being a good upgrade and i can easily fix this one or replace it with an xj one but I m quite pressed for time these days and would like to know if i can just grab a zj one and have it

This Pin was discovered by Brent Wittmeyer Discover and save your own Pins on Pinterest When autocomplete results are available use up and down arrows to review and enter to select Touch device users explore by touch or with swipe gestures